September 20, 2024
Mountain
Cat
“
Use three points
Seven-percent nourishment
”
As the saying goes:“Use three points,Seven-percent nourishment”,After the engineering machinery and equipment are put into use,Timely and effective daily maintenance is very important.。Carefully maintain the equipment before it breaks down and find out the hidden dangers in time.,And can reduce that probability of equipment failure.,Prolong the service life of equipment,Reduce expenses。
Bobcat Skid Steer Loader for its high flexibility、And that versatility is strong,At the municipal、Agriculture、Architecture、It has a wide range of applications in many fields such as gardens.。High frequency of use also means a higher risk of wear and failure,Remember the following important points in times,Maintain and service equipment in a timely manner,Keep your Bobcat Skid Steer Loader in top condition at all times!
01
8 to 10 hours
Engine oil、Hydraulic oil:Every 8 to 10 hours,Check the engine oil once、Hydraulic oil,Add as needed,But don't overfill it.。
Engine air filter:Check for flashing service lights on the display panel,And replace the filter when the service code is present。
Engine cooling system:When the machine is cold,Check coolant level and add premixed coolant as required。Clean oil cooler in time.、Radiator、Fuel cooler、Sundries on A/C condenser and rear grille。
Fuel filter:Clean water from the water separator bowl every 8 to 10 hours。
Lift arm、Lift the linkage、Cylinder、Bob-Tach System、Pivot pin、Wedge:Lubricate with proper grease as required。
02
50 hours
Inspect hydraulic hoses and lines for damage or leaks every 50 hours。Check the parking brake、Pedal、Do the manual controls and steering levers or levers function properly,If there is any fault, deal with it in time.。
First 50 hours of machine operation,Change oil and oil filter element。
03
100 hours
Check battery cables and connections every 100 hours,Clean and tighten as required。If your machine is not used often,It is recommended to start the engine once a week for charging.。
04
250 hours
Every 12 months under standard operating conditions/250 hours(Whichever comes first)Change engine oil and filter once。Special note,Replace every 100 hours of operation under severe conditions。
Engine/Hydrostatic drive belt:Adjust the belt tensioner,Check for wear or damage,Debug or replace as needed。
05
500 hours
Every 12 months or every 500 hours(Whichever comes first)Replace the fuel filter element。
06
1000 hours
Engine Valve:Adjust the engine valves every 1000 hours。
Hydraulic oil filter element:Replace the hydraulic oil filter element every 1000 hours。
Hydraulic oil:Completely replace the hydraulic oil every 1000 hours.。
07
2 years
Change the coolant every 2 years。
Shanghai BMW show —— The grand meeting of the construction machinery industry Shanghai BMW show(bauma CHINA)The largest in Asia、The world's second largest construction machinery industry event。It brings t
November 14-The 15th,Party Secretary of Shaanxi Construction Machinery Co., Ltd.、Chairman Yang Hongjun,Chief Financial Officer Yang Juan and his delegation went to Hainan Pangyuan Machinery Engineering Co., Ltd. to investigate the const
Recently,The construction site of an open-pit iron ore mining project in Liaoning Province is a hot scene.,Count Taishan TuiSE800 mine excavators are on fire.,Work together to speed up the construction period,Press the acceleration key for the efficien
According to Gaogong Industrial Research Institute(GGII) Statistics ,In 2023, the overall sales volume of mining cards in China was about 30,000 units.,The sales volume of new energy mining cards is more than 1500.。With“Side mining、Edge repair&rd
Copyright Notice 2002-2024 global-ce.com Construction Machinery Online. All rights reserved.
Address: Room 901, Building C, Ruipu Mansion, Hongjunying South Road No.15, Chaoyang District, Beijing.100107 P.R.China